Numerical Study on Low Reynolds Mixing ofT-Shaped Micro-Mixers with Obstacles

Document Type: Original Research Paper

Authors

Biomedical Engineering Division, Life Science Engineering Department, Faculty of New Sciences and Technologies, University of Tehran, Tehran, I.R. Iran

Abstract

Micromixers are one of the most crucial components of Lab-On-a-Chip devices with the intention of mixing and dispersion of reagents like small molecules and particles. The challenge facing micromixers is typically insufficient mixing efficiency in basic designs, which results in longer microchannels. Therefore, it is desirable to increase mixing efficiency, in order to decrease mixing length, which enables miniaturization of Lab-On-Chip devices.  This study investigates two different designs of a passive T-shaped micromixer employing several rectangular obstacles and grooves to monitor mixing efficiency with geometry change, while keeping the Reynolds number under 2. The mixing performance of these geometries is studied by numerical study and it was implemented in COMSOL Multiphysics environment. It was clarified that T-shaped micromixer with obstacles and grooved micromixer improved mixing efficiency of the basic design by 37.2% and 43.8%, respectively. Also, it was shown that this increase in mixing efficiency was due to the development of transversal component of flow caused by the obstacles and grooves.

Keywords


[1] I. Bernacka - Wojcik et al., Experimental optimization of a passive planar rhombic micromixer with obstacles for effective mixing in a short channel length, RSC Advances 4 (99) (2014) 56013-56025.

[2] M.S. Virk, A.E. Holdø, Numerical analysis of fluid mixing in T-Type micro mixer, The International Journal of Multiphysics 2 (1) (2008) 107-127.

[3] N.-T. Nguyen, Z. Wu, Micromixers—a review, Journal of Micromechanics and Microengineering 15 (2) (2005) R1-R16.

[4] X.-B. Wang et al., Cell separation by dielectrophoretic field-flow-fractionation. Analytical Chemistry 72 (4) (2000) 832-839.

[5] Y. Shi et al., Radial capillary array electrophoresis microplate and scanner for high-performance nucleic acid analysis, Analytical Chemistry 71 (23) (1999) 5354-5361.

[6] V. Rudyak, A. Minakov, Modeling and Optimization of Y-Type Micromixers, Micromachines 5 (4) (2014) 886-912.

[7] G.S. Jeong et al., Applications of micromixing technology, Analyst 135 (3) (2010) 460-473.

[8] I. Sabotin et al., Optimization of grooved micromixer for microengineering technologies, Informacije MIDEM 43 (2013) 3-13.

[9] Y.Z. Liu, , B.J. Kim, H.J. Sung, Two-fluid mixing in a microchannel, International journal of heat and fluid flow 25 (6) (2004) 986-995.

[10] A. Kumar et al., Effect of geometry of the grooves on the mixing of Fluids in micro mixer channel, in COMSOL Conference (2012).

[11] M. Itomlenskis, P.S. Fodor,  M. Kaufman, Design of Passive Micromixers using the COMSOL Multiphysics software package, in Proceedings of COMSOL Conference (2008).

[12] S. Vanka, G. Luo, C. Winkler, Numerical study of scalar mixing in curved channels at low Reynolds numbers, AIChE journal 50 (10) (2004) 2359-2368.

[13] 1. Bernacka-Wojcik et al., Experimental optimization of a passive planar rhombic micromixer with obstacles for effective mixing in a short channel length, RSC Advances 4 (99) (2014) 56013-56025.

[14] J. Aubin, D.F. Fletcher, C. Xuereb, Design of micromixers using CFD modelling, Chemical Engineering Science 60 (8) (2005) 2503-2516.

[15] Y-C. Lin,., Y.-C. Chung, C.-Y. Wu, Mixing enhancement of the passive microfluidic mixer with J-shaped baffles in the tee channel, Biomedical microdevices 9 (2) (2007) 215-221.

[16] D. Gobby, P. Angeli, A. Gavriilidis, Mixing characteristics of T-type microfluidic mixers, Journal of Micromechanics and microengineering,. 11 (2) (2001) 126.

[17] M. Engler et al., Numerical and experimental investigations on liquid mixing in static micromixers. Chemical Engineering Journal 101 (1) (2004) 315-322.

[18] J.-T. Yang, K.-J. Huang, Y.-C. Lin, Geometric effects on fluid mixing in passive grooved micromixers, Lab on a Chip 5 (10) (2005) 1140-1147.

[19] A. Soleymani, , H. Yousefi, I. Turunen, Dimensionless number for identification of flow patterns inside a T-micromixer, Chemical Engineering Science 63 (21) (2008) 5291-5297.

[20] T. Shih, C.-K. Chung, A high-efficiency planar micromixer with convection and diffusion mixing over a wide Reynolds number range, Microfluidics and Nanofluidics 5 (2) (2008) 175-183.

[21] S.S. Ghadge, N. Misal, Design and Analysis of Micro-Mixer for Enhancing Mixing Performance. International Journal of Emerging Trends in Science and Technology  1 (08) (2014) 1342-1346.

[22] A.A.S. Bhagat, , E.T. Peterson, I. Papautsky, A passive planar micromixer with obstructions for mixing at low Reynolds numbers, Journal of micromechanics and microengineering 17 (5) (2007) 1017.

[23] L. Capretto et al, Micromixing within microfluidic devices in Microfluidics, Springer (2011) 27-68.

[24] J.M. Chen, T.-L. Horng, W.Y. Tan, Analysis and measurements of mixing in pressure-driven microchannel flow, Microfluidics and Nanofluidics 2 (6) (2006) 455-469.

[25] R.B. Bird, W.E. Stewart, E.N. Lightfoot, Transport phenomena (1960).

[26] I. Celik, Procedure for estimation and reporting of discretization error in CFD aaplications. ASME Journal of Fluids Engineering 1 (06) (2008).

[27] M. Jain, A. Rao, K. Nandakumar, Numerical study on shape optimization of groove micromixers, Microfluidics and nanofluidics 15 (5) (2013) 689-699.